logo

C11000 vs C10100 vs C12200 Copper Sheet: Grade Comparison and Selection Guide for Buyers

2026/10/14
최신 회사 블로그 게시물 C11000 vs C10100 vs C12200 Copper Sheet: Grade Comparison and Selection Guide for Buyers

Why Copper Grade Choice Decides Your Project Outcome

Copper sheet is not a single product. C11000, C10100 and C12200 may look identical on the shelf, yet their purity, oxygen content and conductivity differ enough to change how a sheet performs in a busbar, a heat exchanger or an architectural facade. Choosing the wrong grade can mean higher resistance, cracking during bending, or premature corrosion in harsh service. This guide breaks down the three most requested copper sheet grades so sourcing teams can specify with confidence.

SYLAITH productSYLAITH productSYLAITH productSYLAITH product

Quick Comparison of the Three Grades

GradeTypeCopper PurityConductivity (IACS)Typical Use
C11000Electrolytic Tough Pitch (ETP)≥99.90%≈100%Busbar, cable, general electrical
C10100Oxygen-Free Electronic (OFE)≥99.99%≈101%Vacuum devices, high-end electronics
C12200Phosphorized (DHP)≥99.90% + P≈85%Plumbing, heat exchangers, HVAC

C11000 – Electrolytic Tough Pitch Copper

C11000 is the workhorse of the copper industry. With a minimum copper content of 99.90% and roughly 100% IACS conductivity, it delivers an excellent balance of electrical performance, corrosion resistance and cost. It is easy to bend, stamp and weld, which makes it the default choice for copper busbars, electrical connectors and general sheet metal work. For most switchgear, panel and power distribution projects, C11000 copper sheet is the grade that keeps budgets and lead times under control.

C10100 – Oxygen-Free Electronic Copper

C10100 goes one step further. Produced in an oxygen-free environment, it reaches 99.99% purity and about 101% IACS conductivity, with far lower oxygen content than C11000. That matters in vacuum tubes, semiconductors, high-frequency components and magnet windings, where even trace oxygen can cause embrittlement under high heat. If your design calls for hydrogen brazing or ultra-low outgassing, C10100 is worth the premium.

C12200 – Phosphorized Copper

C12200 adds a small amount of phosphorus (typically 0.015–0.040%), which lowers conductivity to roughly 85% IACS but dramatically improves weldability and resistance to dezincification in wet environments. That trade-off makes C12200 the standard for copper tube, plumbing fittings and HVAC heat exchangers. If your priority is thermal transfer and long-term corrosion resistance rather than maximum conductivity, C12200 is the right specification.

How to Choose the Right Grade

  • Need maximum conductivity and cost efficiency? Choose C11000.
  • Working in vacuum, high-frequency or brazing environments? Choose C10100.
  • Handling water, steam or condensate? Choose C12200.
  • Bending, stamping or deep drawing? Confirm temper (soft O, half hard H02, hard H04) before ordering.

Specification Checklist Before You Order

  1. Confirm the grade and actual copper purity requirement.
  2. State the temper that matches your forming process.
  3. Fix the thickness tolerance (for example ±0.02 mm on precision sheets).
  4. Define surface finish: mill, bright, polished or brushed.
  5. Request a mill test certificate and conductivity report with each lot.

Why Buy Copper Sheet from SYLAITH

WUXI SYLAITH SPECIAL STEEL CO., LIMITED (brand SYLAITH) manufactures and exports copper sheet, plate and strip in C11000, C10100 and C12200, cut to your required thickness, width and temper. Every shipment is backed by inspection reports, stable quality and reliable export service. Copper from a dedicated supplier means consistent conductivity, fewer rejections on your line, and a partner who understands the standards your buyers demand.

Request a Quote

Send your drawing, grade, temper and thickness to sales2@slssteel.com and our team will reply within one working day with specification, MOQ, lead time and price basis.

이전 게시물
다음 게시물